加入收藏    設為首頁
熱銷產品
> IGBT DC-Link > 文章正文

IGBT模塊電路雜散電感測量方法

圖1為IGBT半橋拓?fù)潆娐穲D,及當開關IGBT1時產生的電壓電流波形。該電路雜散電感Ls代表所有的分布電感(電容器,母線和IGBT模塊)。
IGBT半橋拓?fù)潆娐窊Q流回路
Fig.1: Half-bridge circuit with current and voltage waveforms when switching IGBT1
Due to the changing current a voltage drop of Ls * dioff/dt occurs across the stray inductance Ls. It is overlayed to the DC link voltage VCC and seen as a voltage spike across the turning-off IGBT1. According to the RBSOA diagram, this spike must be limited to the blocking voltage VCES of the IGBT module (measured at the chip, means measured at the CE auxiliary terminals). Also a derated curve is given in the data-sheet for measurements at the power terminals, taking into account the internal module stray inductance between main and auxiliary terminals of the module.文章來源:http://wllre.cn/il/150.html
換流回路的雜散電感可以通過IGBT在開通時的兩端壓降獲得:當IGBT依然處于阻斷狀態,而電流已經開始上升時,可以測量di/dt及電壓降DV,根據測量值計算電感值,見下式:
Ls = DV / di/dt.
IGBT在開通時電壓電流波形
Fig.2: Switching curves of current and voltage when turning on an IGBT
Example:
i: 400A / div (green) v: 200V / div. (black)
該電壓降發生的時刻,二極管仍然沒有阻斷能力。因此電壓降只能是由雜散電感產生,不需考慮其他的影響。The circuit stray inductance is calculated according to the above shown formula at zero
crossing of current. We get the following values:
DV » 230V
di/dt » 3200A/800ns
Å Ls » 58nH
 
    驗證碼: 點擊我更換圖片
       上海菱端電子科技有限公司:
       聯系人:夏小姐
       服務熱線:021-58979561
       業務咨詢qq:447495955
       業務咨詢qq:1852433657
       業務咨詢qq:513845646
       技術支持qq:313548578
       技術交流群:376450741
       業務咨詢:  點這里給我發消息
       業務咨詢:  點這里給我發消息
       業務咨詢:  點這里給我發消息
       技術支持:  點這里給我發消息
       媒體合作:  點這里給我發消息